IPH4-25-601 Internal Gear Pump
IPH4-25-601 mounting dimensions and replacement checks
Begin with the mounting face of the pump you are replacing. Match the pilot and the two mounting centers, then check that the coupling accepts the keyed shaft. Compare the suction and pressure port positions with the counterclockwise drawing on catalog page 10.
| Interface | Catalog reference |
|---|---|
| Shaft diameter and keyway | Ø25 h7 shaft and 8 h9 keyway |
| Mounting flange pilot | Ø101.6 h8 |
| Mounting centers | 146 mm |
| Port connections | SAE J518C Code 61. Pressure flange No. 11 and suction flange No. 13. |
| Drawing dimension c | 108 mm for IPH 4–25 |
IPH 4–25 installation drawing
Use the counterclockwise (CCW) view and the IPH 4–25 row in the dimensions table.
SAE 2-bolt flange and keyed shaft
For a replacement, send a clear nameplate photo and pictures of the shaft, flange and both port faces. Include drive speed, normal operating pressure and any peak pressure or available installation dimensions.
What the 601 ordering code means
Read the full ordering code as IPH 4-25 601.
| Code | Configuration |
|---|---|
| IPH 4 | Internal gear pump, frame size 4 |
| 25 | Displacement code for 25.7 cm³/rev |
| 6 | Counterclockwise (CCW) rotation with radial suction port |
| 0 | SAE 2-bolt mounting flange |
| 1 | Straight parallel shaft with keyway |
IPH4-25-601 specifications
The IPH 4–25 uses radial and axial sealing gap compensation to limit internal leakage. It is designed for constant-speed drives.
| Parameter | IPH 4–25 catalog data |
|---|---|
| Model | IPH4-25-601 |
| Pump type | Fixed-displacement internal gear pump |
| Geometric displacement | 25.7 cm³/rev |
| Reference delivery at 1,500 rpm | 38.6 L/min |
| Continuous pressure | 250 bar (25 MPa) |
| Peak pressure | 315 bar (31.5 MPa), subject to duty limits below |
| Catalog speed range | 300–3,000 rpm |
| Operating inlet pressure | 0.8–3.0 bar absolute |
| Hydraulic fluid | Mineral hydraulic oil per DIN 51524 Part 2 or 3 |
| Operating oil viscosity | 10–300 cSt |
| Fluid temperature | −20 to +80 °C |
| Fluid cleanliness | ISO 4406 19/17/14 |
| Catalog reference weight | 14.2 kg |
Pressure ratings assume mineral oil at 20–40 cSt and inlet pressure of 0.8–3.0 bar absolute. Peak pressure is permitted for up to 15% of operating time in cycles of no more than one minute. Check allowable peak pressure at nonstandard speeds. Actual delivery depends on operating pressure, viscosity and volumetric efficiency.
IPH 4 delivery curve
Follow the middle curve labeled IPH 4–25 to compare delivery at different operating pressures.
IPH4-25-601 FAQs
Can I order IPH4-25-601 if my nameplate only says IPH 4–25?
IPH 4–25 identifies the pump size and displacement. The 601 suffix specifies counterclockwise rotation with radial suction, an SAE 2-bolt mounting flange and a straight keyed shaft. Compare these three features with your existing pump before ordering.
What shaft and mounting dimensions should I check on IPH4-25-601?
The IPH 4 drawing shows a Ø25 h7 shaft with an 8 h9 keyway, a Ø101.6 h8 mounting pilot and 146 mm mounting centers. Check shaft projection and clearance against your coupling as well.
Which port flanges does IPH4-25-601 use?
The catalog specifies SAE J518C Code 61 connections with pressure flange No. 11 and suction flange No. 13. Use the IPH 4 counterclockwise drawing to confirm the port positions before reusing your piping.
Can IPH4-25-601 run continuously at 315 bar?
The continuous rating is 250 bar. The 315 bar peak rating applies for up to 15% of operating time in cycles of one minute or less, under the catalog’s specified oil viscosity and inlet pressure conditions.
What flow does IPH4-25-601 deliver at 1,500 rpm?
The catalog reference is 38.6 L/min at 1,500 rpm. Use the IPH 4–25 delivery curve to estimate delivery at your system’s operating pressure.
Request a quote for IPH4-25-601
Share your nameplate photo, required quantity and delivery destination. Include the working pressure and drive speed so we can check the configuration.
As a competent manufacturer of diversified Hydraulic Pumps, we are thriving across the globe and we are happy to share the overwhelming positive feedback we have received from satisfied customers across the globe. Our products have won accolades for their superior quality and performance. Consistent positive reviews reflect the trust and satisfaction customers experience after making a purchase.
Join our customers and experience the excellence that sets us apart. Your trust is our motivation and we look forward to exceeding your expectations with our POOCCA hydraulic pump solutions.













